A pool has four walls and a floor. An automatic cover is the fifth wall — the one that closes over the water at the push of a button. It is sold as a luxury; it is actually the hardest-working machine on the pool: it stops evaporation, keeps out dust, locks out children, and holds the water’s warmth, all at once.
Every slat of the cover is a sealed, air-filled tube, so the whole deck of slats floats on the water. The motor never lifts anything — it only rolls the floating deck onto a tube and unrolls it again. Nothing strains, which is why a large cover runs on a surprisingly modest motor. The motor itself lives inside the roller tube, with its power cable entering through a sealed wall passage — a detail that must be designed into the pool, waterproofed, and kept reachable for service.
And here is the fact that decides the drawings: as the cover rolls up, slat wraps upon slat, so the roller grows fatter with the pool’s length — a long pool makes a thick roll, and its housing must fit that roll with room to spare. The one document to demand from any cover supplier before concrete is poured is the pit-dimension table against pool length. A pit sized by guesswork is how covers end up grinding against their own housing.
Every automatic cover is the same machine — floating slats, a tube, a motor. What truly separates one installation from another is where the roll lives. Think of it like parking a car: in a basement built under the house, in a garage beside the house, or in the open driveway.
The roller lives inside the pool itself, permanently underwater — in a recess at the bottom, hidden beneath a grille, a bench or a step. When the cover is open, you see nothing at all: the pool is simply a pool. This is the luxury answer, and it asks the most in return: the recess must be cast into the structure before concrete, the motor must be built for a lifetime underwater, and the slats live in pool water around the clock — one more reason disciplined water chemistry matters. A decision for the drawing board, never for later.
The roller sits just past the pool’s end wall, below deck level, in its own dry chamber with a lid or grating flush with the deck. The cover simply climbs over the wall and curls down into its box. From the deck it is just as invisible as the wet type — but the motor lives dry, so servicing means lifting a lid, not reaching under water. The one rule that decides everything: the dry pit must actually stay dry. A flooded box puts the motor under water, and a roll that fills with water becomes enormously heavy and damages itself. So the pit is built with drainage, like any basement. Suits new builds — and many renovations too, because the digging happens beside the pool, not into it.
The roller stands at the end of the pool on supports, most elegantly dressed as a bench you can sit on. You do see it — but a well-made bench reads as furniture, not machinery. This is the simplest and most affordable automatic cover, and the true retrofit answer: no digging anywhere, installable on a completely finished pool.
| Wet — under the pool floor | Dry — under the deck | Above the deck | |
|---|---|---|---|
| Visible when open? | Nothing at all | Only a flush grating | Yes — ideally as a bench |
| When decided | Before concrete, always | Build or major renovation | Any time, even after handover |
| The motor lives | Underwater, sealed | Dry, under a lid | In the open roller |
| The watchpoint | Water chemistry around slats and motor | The pit must drain — a flooded box wrecks the machine | It occupies deck space |
| Membrane roller | Above-deck slats | Hidden slats (wet or dry) | |
|---|---|---|---|
| What you see | A fabric sheet on a visible roller | Slat deck, roller as a bench | Water only |
| Cost | Lowest | Middle | Highest |
| Child safety | Only when properly tensioned and anchored | Yes, to the safety standard | Yes, to the safety standard |
| Honest position | Entry-level protection; collects debris on top | The working standard | The invisible, premium answer |
A cover sold as child protection must meet a real test — the French standard NF P90-308, written after drowning tragedies, requires the closed cover to bear a child’s weight and resist being opened. Makers meet the second requirement in two ways. One philosophy removes the control: the key leaves the pool with the adult. The other locks the cover automatically the moment it closes, with no human action at all. For a home, either can work. For a hotel — where safety must survive staff turnover, shift changes and busy evenings — only the self-locking kind is truly a barrier, because a barrier that waits for someone to remember it is not one.
Three decisions hide in the slats. Width: a slat is stiff only up to a span — most ranges stop between 4 and 6.5 metres of pool width, so on a wide hotel pool the cover question is settled before any brochure opens. Material: PVC is the working standard; polycarbonate is stronger and clearer; mineral-core composite slats with marine treatment are the premium tier. Colour: clear “solar” slats warm the water by several degrees — a gift in winter, a liability in high summer; opaque light slats reflect instead. The colour follows the climate, not the décor.
First, the chlorinator interlock: under a closed cover chlorine cannot gas off, levels climb, and the trapped chemistry attacks the slats themselves — so on a salt pool, the chlorinator must cut off when the cover closes; good makers wire this as standard. Second, the drive: covers now come with solar-powered drives — no mains cable run to the pool edge at all, which removes an entire electrical scope on retrofits.
Most of the water an open pool loses leaves as vapour, and its heat goes with it — a cover stops nearly all of it (work your own numbers on our Calculators page). It halves the solar collector area a heated pool needs. And in dusty weeks it keeps the pool visibly clean for days — for many owners the first benefit they actually notice. Against all this: a cover is a machine, and machines need service — the track, the motor and the slats inspected on schedule, like everything else worth owning.
Before You Commit
Can you show the pit-dimension table for my pool’s length? Is the safety compliance automatic, or does it depend on a person? What is the slat width limit of this range, and is my pool within it? And does the chlorinator cut off when the cover closes? Vague answers now become a stuck cover later.